Thursday , 28 March 2024

Review: Kyosho DBX 2.0

Review: Kyosho DBX 2.0 | CompetitionX - Tony Phalen

One of the most prestigious racing classes is 1:8th scale. It is like the Formula 1 of RC, and if you’ve been crowned a 1:8th scale World Champion, you are definitely among the elite. This is an enticing thought for some of the newer blood entering our sport, but at the entry level, who can afford the high-dollar supercars it takes to get there? Well Kyosho has a solution. Meet the DBX 2.0, an entry-level 4WD nitro buggy aimed at beginners wanting a taste of 1:8th scale. Unlike the original DBX, the 2.0 features a few upgrades that place it closer to the 1:8th scale family.

THE FACTS
WHO MAKES IT: Kyosho
WHO IT’S FOR: Beginner
HOW MUCH: $315
BUILD TYPE: RTR
VEHICLE TYPE: 1/9 Scale 4WD Nitro Buggy
THE BOTTOM LINE: A fun buggy that is perfect for those wanting to get their feet wet in nitro

Review: Kyosho DBX 2.0 | CompetitionX - Tony Phalen

DESIGN ANALYSIS
• The Kyosho DBX 2.0’s powertrain is a shaft driven 4WD system. Dual 3mm shafts run the length of the buggy and into the front and rear gearboxes. From there, 3mm shafts extend out the the wheels.

• The front, center and rear differentials are fluid-filled and gear driven. This tunable combo makes for a super-durable design that should last a long time.

• To help keep repair costs down, Kyosho has made the front/rear and left-right suspension arms, front/rear knuckles and front/rear shock towers interchangeable.

• Brake bias allows you to adjust how much brake force you want to the front and rear wheels independently. While this is not something that might be important to the everyday driver, it does give you an advantage over your race buddies.

• The DBX 2.0 chassis has multiple motor-mounting holes drilled into it. This should allow you to drop any .18 (or smaller) motor onto the chassis.

• The one piece radio tray is held into place by four screws, allowing easy removal for maintenance.

Review: Kyosho DBX 2.0 | CompetitionX - Tony Phalen

WHAT YOU NEED TO KNOW
– Kyosho has released the DBX 2.0 as a comparably-sized 1:8th scale 4wd nitro buggy. Upon further inspection, my measurements put it just a tick under the typical 1:8th scale size. I contacted Kyosho and it was confirmed that the DBX is a tad smaller than 1:8th scale. So, those of you thinking you are getting a 1:10th scale buggy, rejoice that you are getting something bigger than you thought!

Review: Kyosho DBX 2.0 | CompetitionX - Tony Phalen– The DBX 2.0 rolls on a set of sharp-looking 1:8th scale wheels and tires. While not the softest compound you can buy, these tires should work well and last quite a bit longer than those softies. In addition, any 1:8th scale wheel that incorporates the industry-standard 17mm hex will work on the DBX.

– I’m not a nitro guy and wasn’t really looking forward to starting, breaking in and tuning the GXR18 engine. After charging up my glow igniter and adding fuel, I was greatly surprised when it fired up almost right away! I let it idle through the first tank and then set it down to do some tweaking. It responded well and was actually very easy to tune.

– Dual disc brakes come standard on the DBX 2.0. Also standard is the adjustable brake bias that allows you to fine tune the front and rear braking qualities independently.

Review: Kyosho DBX 2.0 | CompetitionX - Tony Phalen– Kyosho has included their new Syncro 2.4GHz transmitter system. This unique-looking radio includes knobs on a top panel for easy access. The knobs control the trims, EPA and servo reversing. It also has a two position trigger neutral point (70/30 or 50/50), making it ideal for both electric and gas powered vehicles.

– The DBX 2.0 comes equipped with big bore shocks. These oil-filled dampers did a great job of soaking up the pretty rough terrain at our test site. I even had a chance to utilize the threaded bodies for more ride height. Multiple adjustment holes on the shock towers allow you to tune the suspension to your liking.

– One thing that immediately catches your eye is the crazy paint scheme on the racing-bred body. This cab-forward design has hit the offroad buggy market in a big way. By creating more downforce, this helps stabilize the buggy on the track and in the air. Make it pre-cut (and pre-mounted) and add an eccentric 3-color paint scheme (in either blue or red) and you’ve got something that will turn heads!

ITEMS NEEDED
– 8 AAs for the transmitter
– Glow igniter
– Fuel
– Fuel bottle

ITEMS USED
+ 8 MaxAmps AA’s
+ Byron’s Race Blend 20%
+ Dubro Glow Starter
+ Byron Fuel Bottle

TOOLS INCLUDED
+Box wrench & Allen wrenches

TOOLS NEEDED
– A quality Allen Driver set is recommended

PROS & CONS
+ Includes Kyosho’s new 2.4GHz Syncro Transmitter system complete with digital servos
+ Dirt-proof receiver and battery box can be removed with 4 screws
+ Threaded big-bore shocks
+ Massive 105cc fuel tank is capable of around 15 minutes of runtime
+ Tires have pretty good traction
+ Pretty slick looking body and paint scheme

– While the GXR18 engine is a joy to start and tune, it will leave you wanting a LOT more power
– Turnbuckles and drive axles look pretty anemic

Review: Kyosho DBX 2.0 | CompetitionX - Tony Phalen

PERFORMANCE
Test Conditions: Construction site with hard dirt, loose dirt and big rock mounds

STEERING Neutral
The DBX 2.0 houses a Kyosho KS-101BK servo for steering. Rated at 144oz of torque, this servo has no problems wrestling the front tires around. After a few passes through some pretty rough terrain, I did notice a ‘lag’ in steering response. I checked it out and found that the servo saver was pretty loose. Tightening it up and heading back out, that ‘lag’ had disappeared.

BRAKING Good
There are certainly no complaints with the braking power in the DBX 2.0. Another KS-101BK servo is attached to the removable radio tray for throttle/brake duties. This servo has plenty of power to lock up both front and rear brakes and haul the DBX down from any speed.

ACCELERATION Good
I was curious to find out how a 1/8 scale buggy (ok, 1/9 scale) was going to get around using a smaller .18 size engine. I tuned the engine to a tad on the lean side to try and eek out as much power as I could without straining the engine. Overall, the DBX and GXR18 engine had pretty good power to pull itself around and over all the obstacles the construction yard.

SUSPENSION Excellent
You can definitely feel a ‘World-Class’ suspension on the DBX 2.0. The shock package seems near perfect for the battered surface I was running on, and the tuned suspension helped me retain control of the DBX the entire time. Having the ability to have one set of replacement suspension parts is also a bonus! If you added a bit more power, I’m pretty confident that this buggy could hang with some the other big-motor competition!

DURABILITY Excellent
We didn’t experience any major issues with the DBX 2.0 during the test. After the shoot I blew it off with my air compressor and gave it a thorough inspection. Everything appeared great; tires were still glued to the wheels, body didn’t have any cracks, and suspension plastic didn’t show any stress marks. The only,very minor issue was a slightly bent left front turnbuckle. This, however, is an easy fix and shouldn’t keep you out of your racing/bashing situation.

SPECS & TUNING OPTIONS
Kyosho DBX 2.0
DIMENSIONS
LENGTH: 18.7 in. (475mm)
WIDTH: 12.01 in. (305mm)
WHEELBASE: 12.5 in. (320mm)
WEIGHT: 5.5 oz. (2,365g)

SUSPENSION
• Shock position—2 holes in tower, 2 holes in suspension arm
• Camber (F&R)—Adjustable pillow-ball suspension
• Toe—Adjustable turnbuckles
• Wheelbase—Inner suspension arm clips
• Ride height—Threaded shock bodies

DRIVETRAIN
• Diff stiffness—Grease or silicone diff fluids

Review: Kyosho DBX 2.0 | CompetitionX - Tony PhalenMAINTENANCE AND TUNING TIPS
• Check and clean your air filter after every run. Since the filter rests right behind the open front window, it gathers quite a bit of dirt.

• Keep an eye on the motor temperature. Everyone wants a bit more speed and leaning out the engine will do that. Leaning it out too much, however, will also destroy it.

• Since the wheels are spoked, debris can enter the axle area from the front or back of the wheel. Make sure you keep this area clear.

• For easier refills, attach a zip-tie to the fuel filter lid. This will help open the tank without having to reach into the body.

THE FINAL WORD
The Kyosho DBX 2.0 is a lot of fun. While it is a sizeable rig (at 5.5lb) for a .18 size engine, the GXR18 is the right choice for beginners wanting to learn the ropes of nitro cars. It’s extremely easy to tune and starts each time with a short pull of the starter rope (I should know…I kept running out of gas)! I asked a couple of the construction guys what they thought and most of them said it looked pretty fast. That’s good since that is who this vehicle is aimed at; entry-level nitro enthusiasts that want an 1/8-scale buggy without the intimidation of 1/8-scale costs.

LINKS
Kyosho, www.kyoshoamerica.com, (949) 454-8854
Max Amps, www.maxamps.com, (888) 654-4450
Byron Fuels, www.byronfuels.com, (712) 364-3165

About Tony Phalen

Tony Phalen - As an avid RC enthusiast, Tony has been building, bashing and racing RC Cars for over 30 years. He has participated in every kind of surface racing events - 1/18 scale trucks, 1/10 scale TC, Rock Racers, Rally - if it had wheels, he's raced it! He's also worked on both sides of the industry fence; collaborating with many major manufacturers (as well as being a sponsored driver) to working for a high-profile industry magazine. During this time he has learned many tricks, tips and techniques and is sharing that knowledge on CompetitionX - the most informative RC website on the internet!

Check Also

Video: Tamiyas Toyota Supra on the BT-01 Chassis - First Drive | CompetitionX

Video: Tamiya’s Toyota Supra on the BT-01 Chassis – First Drive | CompetitionX

There is alot of buzz surrounding the new BT-01 chassis from Tamiya. This is mainly …

2 comments

  1. Is it possible to put a bigger engine than a .18 in it? I’m looking at buying a .28 engine made by Hobao and wondered if it would fit because it is almost a 1/8.

  2. In stock form, no, it won’t accept anything larger than a .18 engine. I haven’t heard about any conversions yet but I’m sure there are some available. I did a quick Google search and didn’t see anything so you might have to do a little more thorough search. Good luck.