Friday , 29 March 2024

Speed Passion LM-1 LeMans Build – Part 4 – Front Suspension

Speed Passion LM-1 LeMans Build
Speed Passion LM-1 LeMans Build

The Build – Part 4
If Part 4 of the LM-1 build, we assemble and attach the front end. It’s a simple, double a-arm setup that features a pillow-ball upper arm for quick and easy camber adjustments.

Build Notes:
Threadlock will be needed in a few of these steps, so have some ready!

Pre-compress the springs prior to installation. This gives them a quick ‘set’.

The LM-1 have 2 options for the front axle; inline and trailing (you can read about both here: Inline/Trailing Axle. For this build, I’m using the trailing per the instructions.

Speed Passion LM-1 LeMans Build - Part 40 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 40 – Rear Pod
We start off by attaching the caster blocks to the lower arm brace. The kit comes with multiple blocks, but we are starting out with the 10 degree per the manual. Note the orientation of the blocks.

Speed Passion LM-1 LeMans Build - Part 41 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 41 – Rear Pod
The next step is attaching the upper arms to the caster blocks. To assemble, slide the pin through the upper arm and caster block. Before pushing all the way through, insert 2 1mm spacers on each side as shown. Once you’ve pushed it through all the way, secure with the two 2x5mm socket screws (not shown simply because I forgot to do it).

Speed Passion LM-1 LeMans Build - Part 42 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 42 – Rear Pod
Insert a 3mm ballstud into each upper arm. These are for a front damper that will be installed at a later time.

Speed Passion LM-1 LeMans Build - Part 43 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 43 – Rear Pod
Drop the upper arm assembly into position and secure with the 4 3x6mm button head screws. Do not overtighten.

Speed Passion LM-1 LeMans Build - Part 44 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 44 – Rear Pod
Build 3 turnbuckles; 2 steering and one drag link. The lengths given will be a good start.

Speed Passion LM-1 LeMans Build - Part 45 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 45 – Rear Pod
Pop the steering links on as well as the drag link. Note the orientation of the two steering links; the ‘line’ on the adjustment square (on the turnbuckles) should both be pointing the same direction.

Speed Passion LM-1 LeMans Build - Part 46 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 46 – Rear Pod
Attach the ballstud to the steering block. Don’t forget to use a 2mm spacer on both sides. You might also want to put a drop of threadlock here.

Speed Passion LM-1 LeMans Build - Part 47 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 47 – Rear Pod
Slide the steering pivot ball into the steering block and CAREFULLY thread the plastic stopper screw into place. This screw is extremely easy to crossthread to take your time here. Also slide the axle into place. We’re setting it up as a trailing axle per the instructions.

Speed Passion LM-1 LeMans Build - Part 48 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 48 – Rear Pod
As you can see from this pic, the plastic stopper screw is flush with the steering block, not all crooked and crossthreaded. The steering pivot ball should also have extremely free movement.

Speed Passion LM-1 LeMans Build - Part 49 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 49 – Rear Pod
Slide a .5mm and a 1mm shim onto the kingpin, followed by the suspension spring.

Speed Passion LM-1 LeMans Build - Part 50 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 50 – Rear Pod
Press the kingpin though the bottom of the front arm, up through the 3 1mm spacers and into the steering block. Thread it in slowly. I initially used the 3mm spacing per the instructions but ended up at about 3.5mm.

Speed Passion LM-1 LeMans Build - Part 51 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 51 – Rear Pod
Thread the steering pivot ball into the upper arm as shown. There are no settings for from camber at this point, but I have mine set at about 3.25mm (of the steering pivot ball shaft showing). This will probably be a good start.

Speed Passion LM-1 LeMans Build - Part 52 - Rear Pod
Speed Passion LM-1 LeMans Build – Part 52 – Rear Pod
Finally, pop the steering links onto the steering blocks.

Part 5 – Assembling the rear suspension.
Back to the Speed Passion LM-1 LeMans Build List

About Tony Phalen

Tony Phalen - As an avid RC enthusiast, Tony has been building, bashing and racing RC Cars for over 30 years. He has participated in every kind of surface racing events - 1/18 scale trucks, 1/10 scale TC, Rock Racers, Rally - if it had wheels, he's raced it! He's also worked on both sides of the industry fence; collaborating with many major manufacturers (as well as being a sponsored driver) to working for a high-profile industry magazine. During this time he has learned many tricks, tips and techniques and is sharing that knowledge on CompetitionX - the most informative RC website on the internet!

Check Also

Video: Tamiyas Toyota Supra on the BT-01 Chassis - First Drive | CompetitionX

Video: Tamiya’s Toyota Supra on the BT-01 Chassis – First Drive | CompetitionX

There is alot of buzz surrounding the new BT-01 chassis from Tamiya. This is mainly …